The integration of metals and polymers in the same component to couple the best properties and advantages of both these classes of materials can be useful for engineering applications. In this scenario, the aim of this paper is to integrate additive manufacturing of composites with cold spray deposition of metal particles: in particular, 3D-printed carbon fibre-reinforced plastics (CFRP) panels were coated with aluminium particles to couple the lightweight and high mechanical properties of CFRP with high wear resistance and hardness of metals. CFRP panels have been produced by using the Fused Filament Fabrication (FFF) technology, then the panels have been coated with aluminium particles by using a low pressure cold spray facility. Panels with various stratification sequences have been produced to investigate the feasibility of the process and to highlight the influence of the lay-up strategy on the whole process; the parameters of the cold spray process have been also optimized to ensure an effective deposition. Adhesion tests, distortion measurements, cross-section observations and surface coverage measurements have been chosen as response outputs to evaluate the effectiveness of the process and to assess the influence of the process parameters. The integration between FFF of CFRPs and cold spray deposition of aluminium particles has been proved, values of surface coverage close to 100% and good values of adhesion strength (close to 4 MPa) have been achieved; moreover, the presence of the fibres, giving a higher stiffness to the substrate, avoids the occurrence of distortion phenomena during the deposition. It was also proved that the printing parameters influence the deposition: an increase in the infill density from 30% to 50% leads to an increase in the adhesion strength up to 40%. In summary, the results obtained proved the feasibility of the process and allowed to enucleate directions of future research.
Integrating 3D printing of polymer matrix composites and metal additive layer manufacturing: surface metallization of 3D printed composite panels through cold spray deposition of aluminium particles / Perna, A. S.; Viscusi, A.; Gatta, R. D.; Astarita, A.. - In: INTERNATIONAL JOURNAL OF MATERIAL FORMING. - ISSN 1960-6206. - 15:2(2022). [10.1007/s12289-022-01665-9]
Integrating 3D printing of polymer matrix composites and metal additive layer manufacturing: surface metallization of 3D printed composite panels through cold spray deposition of aluminium particles
Perna A. S.;Viscusi A.;Astarita A.
2022
Abstract
The integration of metals and polymers in the same component to couple the best properties and advantages of both these classes of materials can be useful for engineering applications. In this scenario, the aim of this paper is to integrate additive manufacturing of composites with cold spray deposition of metal particles: in particular, 3D-printed carbon fibre-reinforced plastics (CFRP) panels were coated with aluminium particles to couple the lightweight and high mechanical properties of CFRP with high wear resistance and hardness of metals. CFRP panels have been produced by using the Fused Filament Fabrication (FFF) technology, then the panels have been coated with aluminium particles by using a low pressure cold spray facility. Panels with various stratification sequences have been produced to investigate the feasibility of the process and to highlight the influence of the lay-up strategy on the whole process; the parameters of the cold spray process have been also optimized to ensure an effective deposition. Adhesion tests, distortion measurements, cross-section observations and surface coverage measurements have been chosen as response outputs to evaluate the effectiveness of the process and to assess the influence of the process parameters. The integration between FFF of CFRPs and cold spray deposition of aluminium particles has been proved, values of surface coverage close to 100% and good values of adhesion strength (close to 4 MPa) have been achieved; moreover, the presence of the fibres, giving a higher stiffness to the substrate, avoids the occurrence of distortion phenomena during the deposition. It was also proved that the printing parameters influence the deposition: an increase in the infill density from 30% to 50% leads to an increase in the adhesion strength up to 40%. In summary, the results obtained proved the feasibility of the process and allowed to enucleate directions of future research.I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.
