We investigated the influence of design parameters and operational conditions on lateral solid mixing in fluidized beds adopting the Eulerian-Eulerian modeling approach. To quantify the rate at which solids mix laterally, we used a lateral dispersion coefficient (Dsr). Following the usual approach employed in the literature, we defined Dsr by means of an equation analogous to Fick[U+05F3]s law of diffusion. To estimate Dsr, we fitted the void-free solid volume fraction radial profiles obtained numerically with those obtained analytically by solving Fick[U+05F3]s law. The profiles match very well. Our results show that Dsr increases as superficial gas velocity and bed height increase; furthermore, it initially increases with bed width, but then remains approximately constant. The values of Dsr obtained numerically are larger than the experimental ones, within the same order of magnitude. The overestimation has a twofold explanation. On one side, it reflects the different dimensionality of simulations (2D) as compared with real fluidized beds (3D), which affects the degrees of freedom of particle lateral motion. On the other, it is related to the way frictional solid stress was modeled: we employed the kinetic theory of granular flow model for the frictional solid pressure and the model of Schaeffer (1987) for the frictional solid viscosity. To investigate how sensitive the numerical results are on the constitutive model adopted for the frictional stress, we ran the simulations again using different frictional models and changing the solid volume fraction at which the bed is assumed to enter the frictional flow regime (ϕmin). We observed that Dsr is quite sensitive to the latter. This is because this threshold value influences the size and behavior of the bubbles in the bed. We obtained the best predictions for ϕmin=0.50. The results show that accurate prediction of lateral solid dispersion depends on adequate understanding of the frictional flow regime, and accurate modeling of the frictional stress which characterizes it.

Numerical simulations of lateral solid mixing in gas-fluidized beds / Oke, Oyebanjo; Lettieri, Paola; Salatino, Piero; Solimene, Roberto; Mazzei, Luca. - In: CHEMICAL ENGINEERING SCIENCE. - ISSN 0009-2509. - 120:(2014), pp. 117-129. [10.1016/j.ces.2014.08.049]

Numerical simulations of lateral solid mixing in gas-fluidized beds

SALATINO, PIERO;
2014

Abstract

We investigated the influence of design parameters and operational conditions on lateral solid mixing in fluidized beds adopting the Eulerian-Eulerian modeling approach. To quantify the rate at which solids mix laterally, we used a lateral dispersion coefficient (Dsr). Following the usual approach employed in the literature, we defined Dsr by means of an equation analogous to Fick[U+05F3]s law of diffusion. To estimate Dsr, we fitted the void-free solid volume fraction radial profiles obtained numerically with those obtained analytically by solving Fick[U+05F3]s law. The profiles match very well. Our results show that Dsr increases as superficial gas velocity and bed height increase; furthermore, it initially increases with bed width, but then remains approximately constant. The values of Dsr obtained numerically are larger than the experimental ones, within the same order of magnitude. The overestimation has a twofold explanation. On one side, it reflects the different dimensionality of simulations (2D) as compared with real fluidized beds (3D), which affects the degrees of freedom of particle lateral motion. On the other, it is related to the way frictional solid stress was modeled: we employed the kinetic theory of granular flow model for the frictional solid pressure and the model of Schaeffer (1987) for the frictional solid viscosity. To investigate how sensitive the numerical results are on the constitutive model adopted for the frictional stress, we ran the simulations again using different frictional models and changing the solid volume fraction at which the bed is assumed to enter the frictional flow regime (ϕmin). We observed that Dsr is quite sensitive to the latter. This is because this threshold value influences the size and behavior of the bubbles in the bed. We obtained the best predictions for ϕmin=0.50. The results show that accurate prediction of lateral solid dispersion depends on adequate understanding of the frictional flow regime, and accurate modeling of the frictional stress which characterizes it.
2014
Numerical simulations of lateral solid mixing in gas-fluidized beds / Oke, Oyebanjo; Lettieri, Paola; Salatino, Piero; Solimene, Roberto; Mazzei, Luca. - In: CHEMICAL ENGINEERING SCIENCE. - ISSN 0009-2509. - 120:(2014), pp. 117-129. [10.1016/j.ces.2014.08.049]
File in questo prodotto:
Non ci sono file associati a questo prodotto.

I documenti in IRIS sono protetti da copyright e tutti i diritti sono riservati, salvo diversa indicazione.

Utilizza questo identificativo per citare o creare un link a questo documento: https://hdl.handle.net/11588/626122
Citazioni
  • ???jsp.display-item.citation.pmc??? ND
  • Scopus 30
  • ???jsp.display-item.citation.isi??? 26
social impact